|
|
|
|
|
|
| |
|
|
 |
 |
|
 |
|
 |
| |
|
| |
|
| |
|
| |
|
| |
|
|
|
 |
|
|
|
|
 |
Saw Head Frame |
|
|
|
|
The rigid 'C' section frame carries the mountings for the two band wheels, heavy duty worm drive gear reducer, the band drive motor and saw guide arm mounting supports. |
|
|
|
|
|
|
Band Wheels & Drive System |
|
|
|
|
The inverter controlled band drive motor is directly coupled to the worm gear reducer eliminating friction losses of a variable speed pulley drive. The drive wheel transmission is designed and manufactured by Amada to provide a high efficiency speed reduction, which requires no external cooling to deliver more power to the drive wheel. Band speed is set on using the band speed adjustment knob on the control panel. |
|
|
|
|
|
|
Canted Head and Single Column Mounting |
|
|
|
|
The head is canted 8° to enable the machine to cut rolled sections e.g. I beams or rectangular tubing at significantly faster rates because the blade is never in full contact with the horizontal section of the material. The single column mounting enables the saw guides to be much closer together compared to scissor type machines which improves the cutting performance. |
|
|
|
|
|
|
Full Stroke Clamping Vise |
|
|
|
|
The full stroke clamping vise reduces the operator's setup time for different widths of material. |
|
|
|
|
|
|
Manual Vise Inching Control |
|
|
|
|
The vise inching control enables the operator to more accurately locate the work piece for the cut because he can inch the vise until it is just touching the material but not clamped hard. Then with the help of the shadow line projector, make any small adjustment to the position to produce the desired cut. |
|
|
|
|
|
|
Guarding |
|
|
|
|
The saw band is constrained within the heavy gage guarding in all non-cutting areas. |
|
|
|
|
|
|
|
|
|
|
 |
|
|
|
|
|
| Cutting capacity |
|
|
Round work (Diameter) |
|
: |
320mm(12.6 in.) with sawhead at 0°
220 mm (8.7 in.) with sawhead at 45° |
|
|
Rectangular work (W X H) |
|
: |
400 x 280 mm (15.7 x 11 in.) with sawhead
at 0°
220 x 280 mm (8.7 x 11 in.) with sawhead at
45° |
|
| Motors |
|
|
Saw blade |
|
|
2.2 kW (3HP), 4 P, 200 V, 50/60 Hz |
|
|
Hydraulic pump |
|
|
0.75 kW (1HP), 4 P, 200 V, 50/60 Hz |
|
|
Cutting fluid pump |
|
|
0.06 kW (0.08HP), 2 P, 200 V, 50/60 Hz |
|
|
Wire brush |
|
|
0.04 kW (0.05HP), 4 P, 200 V, 50/60 Hz |
|
| Control circuit voltage |
|
: |
AC 100 V |
|
| Saw blade |
|
|
Dimensions (W x T x L) |
|
|
32 x 1.066 x 3885 mm
(1-1/4 x 0.042 x 153 in.) |
|
|
Speed |
|
|
30-100 m/min (100-325 ft/min)
(inverter variable speed change) |
|
|
Tension |
|
|
Manually-operated spring type (with saw
blade breakage detection function) |
|
| Vise |
|
|
Type |
|
|
One-piece vise |
|
|
Operation |
|
|
Hydraulic control (full-stroke type) |
|
| Cutting fluid |
|
|
Tank capacity |
|
: |
40 liters (10.7 US gal) |
|
|
Pump type |
|
: |
Centrifugal |
|
| Hydraulic oil |
|
|
Tank capacity |
|
: |
40 liters (10.7 US gal) |
|
|
Pump type |
|
: |
Variable-discharge vane |
|
|
Set pressure |
|
: |
2.7 MPa (27 kgf/cm2 or 391 psi) |
|
| Saw Blade control |
|
|
Raised position setting |
|
|
Manual setting dial |
|
|
Cutting control |
|
|
Hydraulic pressure - flow control value |
|
| Chip collection |
|
: |
Chip box accumulation |
|
| Table Height (above floor) |
|
|
760 mm (29.9 in.) |
|
| Pass line |
|
: |
770 mm (30.3 in.) |
|
| Maximum allowable loading capacity |
|
|
400 kg (880 lb) |
|
| Machine dimensions (W x D x H) |
|
|
1970 x 1430 x 1865 mm
(77.6 x 56.3 x 73.4 in.) |
|
| Machine weight |
|
|
900 kg (1990 lb) |
|
| Power supply Voltage 200V |
|
|
|
|
|
 |
|
45° Swivel |
|
Variable blade running speed by inverter |
|
Light beam marking |
|
Blade break limit switch |
|
Vise pressure control valve |
|
Work support roller |
|
Short work support bar |
|
Side cover |
|
|
|
|
|
|
|
|
|
Note: Specifications may change without notice at the sole discretion of Amada's Engineering Department |
|
