click to enlarge
Click to download Pdf
 
   
   
   
   
 
 
Saw Head Frame
The rigid 'C' section frame carries the mountings for the two band wheels, heavy duty worm drive gear reducer, the band drive motor and saw guide arm mounting supports.
Band Wheels & Drive System
The inverter controlled band drive motor is directly coupled to the worm gear reducer eliminating friction losses of a variable speed pulley drive. The drive wheel transmission is designed and manufactured by Amada to provide a high efficiency speed reduction, which requires no external cooling to deliver more power to the drive wheel. Band speed is set on using the band speed adjustment knob on the control panel.
Canted Head and Single Column Mounting
The head is canted 8° to enable the machine to cut rolled sections e.g. I beams or rectangular tubing at significantly faster rates because the blade is never in full contact with the horizontal section of the material. The single column mounting enables the saw guides to be much closer together compared to scissor type machines which improves the cutting performance.
Full Stroke Clamping Vise
The full stroke clamping vise reduces the operator's setup time for different widths of material.
Manual Vise Inching Control
The vise inching control enables the operator to more accurately locate the work piece for the cut because he can inch the vise until it is just touching the material but not clamped hard. Then with the help of the shadow line projector, make any small adjustment to the position to produce the desired cut.
Guarding
The saw band is constrained within the heavy gage guarding in all non-cutting areas.
 
 
  Cutting capacity
Round work (Diameter)
:
 320 mm (12.6 in.) with sawhead at 0°
200 mm (7.9 in.) with sawhead at 45°
100 mm (3.9 in.) with sawhead at 60°
Rectangular work (W X H)
:
 400 x 280 mm (15.7 x 11 in.) with sawhead at 0°
200 x 280 mm (7.9 x 11 in.) with sawhead at 45°
100 x 280 mm (3.9 x 11 in.) with sawhead at 60°
   Motors
Saw blade
:
 2.2 kW (3 HP), 4 P, 200 V, 50/60 Hz
Hydraulic pump
:
 0.75 kW (1 HP), 4 P, 200 V, 50/60 Hz
Cutting fluid pump
:
 0.06 kW (0.08 HP), 2 P, 200 V, 50/60 Hz
Wire brush
:
 0.04 kW (0.05 HP), 4 P, 200 V, 50/60 Hz
   Environment
Supply voltage
:
   AC 200/220V ± 10%, 50/60 Hz
Temperature
:
   0 to 40°C (32 to 104°F) during operation and
-5 to +50°C (23 to 122°F) during stoppage
  Humidity
:
   30 to 90% during operation and 10 to 95% during stoppage (without condensation)
   Control circuit voltage
:
 DC 24V
  Saw blade
Dimensions (W x T x L)
:
   32 x 1.066 x 3885 mm (1-1/4 x 0.042 x 153 in.)
Speed
:
 30 to 100 m/min (100 to 325 ft/min) (inverter variable speed change)
Tension
:
   Manually-operated spring type (with saw blade breakage detection function}
   Vise
Type
:
 One-piece vise
Operation
:
 Hydraulic control (full-stroke type)
Work absence detector
:
 Minimum detectable work width: 20 mm (0.8 in)
  Cutting fluid
Tank capacity
:
 40 liters (10.7 US gal)
Pump type
:
 Centrifugal
Pump capacity
:
 45/52 liters/min (11.9/13.7 US gal/min) at 50/60 Hz
  Hydraulic oil
Tank capacity
:
 40 liters (10.7 US gal)
Pump type
:
 Variable-discharge vane
Pump capacity
:
 10.4/12.5 liters/min (2.7/3.3 US gal/min) at 50/60 Hz
Set pressure
:
 2.7 MPa (27 kgf/cm2 or 391 psi)
  Saw Blade control
UP
Automatic
:
 Hydraulic automatic rise (automatic stop at upper limit)
Manual
:
 Inching up by pushbutton control
Raised position setting
:
 Automatic setting with quick approach
DOWN
Automatic
:
 Rapid approach by quick approach
Manual
:
 Inching down by pushbutton control
Feed control
:
 Hydraulic pressure-flow control valve
Slip detection
:
 Automatic stop by overload, jam, or breakage
  Work feed
Type
:
   Hydraulic shuttle
Remnant length
:
 70 mm (2.8 in.) for cutting single piece of work
(when clamp allowance is 10 mm (0.4 in.) )
  Chip collection
:
 Chip box accumulation
  Table height (above floor)
:
 770 mm (30.3 in.)
   Maximum allowable loading capacity
:
 400 kg (880 lb)
   Machine dimensions (W x D x H)
:
 2140 x 2345 x 1865 mm (84.2 x 92.3 x 73.4 in.)
   Machine weight
:
 Approx. 1600 kg (3528 lb)
   Automatic cut-to-length function
Number of input stations
:
 1
Part length
:
 25.0 to 999.9 mm in 0.1-mm increments (1 to 99.999 in. in 0.001-in. increments)
Number of parts
:
 1to 9999 per station
Kerf compensation
:
 Automatic kerf compensation (automatic calculation during long work feed)
*Never stack cut during automatic operation. Otherwise the front vise may improperly feed the work.
*When a radio is used around the machine. it may receive noise from the inverter of the machine. Contact AMADA for reducing this noise.
Power supply Voltage 200V
 
  Note: Specifications may change without notice at the sole discretion of Amada's Engineering Department
 
Copyright © 2011 Tru-Cut Tools (I) Pvt. Ltd.